Check out the video above or the step by step guide below for assistance with this repair

iFixit iPhone 17 Pro Screen Replacement Guide

Here are some tools you may need to help you complete the repair.

Please note: A discounted simple toolset with the tools you need is available in a pop-up when you add this product to cart

• #000 1.5mm Metal Phillips Screwdriver Tool (PH000)
• P2 Metal Pentalobe 0.8mm Screwdriver Tool
• Y000 Metal Triwing Tri-Point 0.6mm Screwdriver Tool
• Large Blue Suction Cup Opening Tool
• Mechanic AK-15 King ESD Anti-Static Stainless Steel Red Curved Tweezers
• iGadget Plastic Triangle Opening Picks (set of 5)
• 5x iGadget Plastic Flexible Opening Cards
• Nylon Antistatic Spudger Pry Tool
• Or get the P2, Y000 and #000 screwdrivers, suction cup, tweezers, opening picks, opening cards and spudger together in our 8 Piece iPhone Repair Toolkit
• iSclack Evo (Gen 3) Suction Cup Opening Tool for phones and tablets by Dottorpod
• uFix iOpener Microwaveable Heated Bag Opening Tool
• iHold Evo Screen Holding Opening Tool for iPads and iPhones with USB-C Adapter by Dottorpod
• 1mm Tesa Tape 61395 Roll Double Sided Adhesive Tape (50m)
• iGadget Plastic Alcohol 200mL Bottle with Pump Top
• iGadget Universal Magnetic Work Project Mat with Marker (30cm x 25cm)

Here are some helpful tips to assist you in completing a safe repair on your device. If you are unsure of something or have any questions, please feel free to contact us either by phone (0508 IGADGET) or by email

• Drain the battery below 25% before you start on this repair
• Always power down your device prior to working on it
• Track your screws on a screw mat or tape them to a drawing of your phone. This repair uses two 7.5mm pentalobe screws at the bottom, a small cross-head screw on each of the battery and screen connector covers, and two 1.0mm Y000 screws on the front sensor bracket
• Remove the two 7.5mm pentalobe screws either side of the USB-C port, then heat the bottom edge to soften the adhesive
• Slide the pick under the plastic bezel, not between the bezel and the glass, and no deeper than 3mm. The screen opens from the right-hand side like a book - the screen and sensor cables are on the left, so stop before the volume-up button on the left edge
• Always unplug the battery before you remove any other parts. Keep metal tools away from the battery, and never bend, crush or puncture it. Remove the battery connector cover and unplug the battery first, then the screen and ambient light sensor connectors. When reassembling, connect the screen connectors first and the battery last, pressing each down gently until it clicks - don't force it
• Transfer the front sensors (ambient light sensor and microphone) from your old screen - the earpiece and Face ID camera stay in the phone, so leave them alone. Remove the bracket (two 1.0mm Y000 screws), warm the area, lift the fragile sensors by the tab underneath with a spudger or opening card and re-stick the cable with Tesa tape
• For a clean pairing, run Repair Assistant (Settings > General > About > Parts and Service History) with the front sensor flex unplugged. Once the screen is paired, power down and plug the sensors in
• Test touch, display and Face ID before sealing the phone, and don't peel off the protective film or any stickers until it's all working
• Clean off all the old adhesive with isopropyl alcohol and fit the new screen adhesive supplied in the box to keep dust and moisture out. Lower the screen top edge first, then press firmly round the edges
• Once the repair is finished, turn True Tone on in Settings > Display & Brightness (iOS 18 or later). Don't write True Tone data to this screen with a programmer, as it may cause issues