Check out the video above or the step by step guide below for assistance with this repair

iFixit iPhone 7 Plus LCD and Digitizer Replacement Guide

Here are some tools you may need to help you complete the repair.

Please note: A discounted simple toolset with the tools you need is available in a pop-up when you add this product to cart

• P2 Metal Pentalobe 0.8mm Screwdriver Tool
• Y000 Metal Triwing Tri-Point 0.6mm Screwdriver Tool
• #000 1.5mm Metal Phillips Screwdriver Tool (PH000)
• Large Blue Suction Cup Opening Tool
• Mechanic AK-15 King ESD Anti-Static Stainless Steel Red Curved Tweezers
• iGadget Plastic Triangle Opening Picks (set of 5)
• 5x iGadget Plastic Flexible Opening Cards
• Nylon Antistatic Spudger Pry Tool
• Or get the P2, Y000 and #000 screwdrivers, suction cup, tweezers, opening pick, opening card and spudger together in our 8 Piece iPhone Repair Toolkit
• iSclack Evo (Gen 3) Suction Cup Opening Tool for phones and tablets by Dottorpod
• uFix iOpener Microwaveable Heated Bag Opening Tool
• iHold Evo Screen Holding Opening Tool for iPads and iPhones with USB-C Adapter by Dottorpod
• iGadget Plastic Alcohol 200mL Bottle with Pump Top
• 10mm High Temperature Heat Resistant Polyimide Board Repair Tape (30m)

Here are some helpful tips to assist you in completing a safe repair on your device. If you are unsure of something or have any questions, please feel free to contact us either by phone (0508 IGADGET) or by email

• Drain the battery below 25% before you start on this repair
• Always power down your device prior to working on it
• Track your screws, they are different lengths: two 3.4mm P2 pentalobe screws at the bottom, four Y000 on the lower display cable bracket (three 1.2mm, one 2.6mm), three Y000 on the front panel sensor bracket (one 1.3mm, two 1.0mm), five Phillips on the earpiece speaker bracket (1.8mm to 2.8mm) and four Y000 on the home button bracket (one 1.1mm, three 1.3mm). Use a screw mat to keep them in place
• Remove the two pentalobe screws beside the Lightning port, warm the bottom edge and lift the screen with a suction cup (not over the home button). Slide picks in no more than 3mm deep and keep them away from the right edge, where the display cables run. Don't lift the screen more than 15 degrees until the plastic clips along the top edge are free, then open it like a book from the left side, hinged on the right
• Always unplug the battery before you remove any other parts. Keep metal tools away from the battery, and never bend, crush or puncture it. The battery connector is under the lower display cable bracket: unplug it first, then the two display cables and the front panel sensor cable. Reconnect each connector by pressing one end at a time, never the middle
• Carefully transfer your original home button - Touch ID only works with the home button your phone came with, and if its flex cable breaks you will lose Touch ID and home button features. Warm the area and use a spudger to gently pry underneath the flex cable to loosen the glue, and don't overtighten the home button bracket screws on reassembly
• Move the metal back plate (LCD shield) across from your old screen, as it is not included with the new screen. If yours is bent, we sell the iPhone 7 Plus Rear LCD Shield Backplate
• Transfer the earpiece speaker, then the front camera and sensor cable (front camera, proximity and ambient light sensors and microphone), as they are not included with the new screen. Warm the top edge before easing the sensors off, don't touch the earpiece's four spring contacts (clean them with isopropyl alcohol if you do), and make sure the black insulating tape over the cable contacts is in place, or cover them with Kapton tape. See the iFixit guide for each step
• Test touch, 3D Touch, display, earpiece, front camera, proximity and Touch ID before sealing the phone, and don't peel off the protective film or any stickers until it's all working
• Opening your iPhone 7 Plus breaks its factory water-resistance seal. Clean off the old adhesive with isopropyl alcohol and fit the new screen gasket adhesive included in the box when you reassemble it.