
Product Details
Lines, dead pixels, colour bleed or no picture on your iPad 2? On the iPad 2 the LCD sits under a separate glass and touch digitiser, so if touch still works you only need to replace the LCD.
Also for the iPad 2: Glass and Digitiser with Home Button (when the glass is cracked)
- LCD ONLY - Just the display panel, so if your glass is fine you don't pay for a new screen front.
- SAME RESOLUTION AS THE ORIGINAL - 1024 x 768 at 132 ppi, matching the display your iPad 2 came with.
- SENT FROM NZ STOCK - Shipped from our New Zealand stock, so there's no waiting weeks for a part to arrive from overseas.
Part Includes:
- 9.7-inch LCD panel
- 12 Month Warranty
Please Note
Does NOT fit the iPad 3 or iPad 4, which have a sharper Retina display and take a different LCD, or the iPad Air. Check the A number on the back of your iPad.
Please Note
This part will either be brand new or a used genuine Apple LCD in full working order.
Specifications
- Type: LCD display panel only (no glass or touch)
- Display Size: 9.7-inch (diagonal)
- Resolution: 1024 x 768 pixels (132 ppi)
- Refresh Rate: 60Hz
- Pairing: Not needed. This iPad doesn't check its screen, so no Unknown Part message.
- Warranty: 12 Months
Compatible Model Numbers
iPad 2 WiFiModel Number (A Number)
- A1395
iPad 2 WiFi Model NumbersHow do I find my Model number?
Model Identifier
- iPad2,1
- iPad2,4
EMC Number
- EMC 2415
- EMC 2560
Device Number (M Number)
- MC769
- MC770
- MC954
- MC979
- MC980
- MC981
- MC989
- MC916
iPad 2 WiFi + CellularModel Number (A Number)
- A1396
- A1397
iPad 2 WiFi + Cellular Model NumbersHow do I find my Model number?
Model Identifier
- iPad2,2
- iPad2,3
EMC Number
- EMC 2416
- EMC 2424
Device Number (M Number)
- MC755
- MC763
- MC764
- MC773
- MC774
- MC775
- MC957
- MC982
- MC983
- MC984
- MC985
- MC986
- MC987
- MC992
Installation Help
Check out the video above or the step by step guide below for assistance with this repair
iFixit iPad 2 LCD Replacement Guide
Here are some tools you may need to help you complete the repair.
Please note: A discounted simple toolset with the tools you need is available in a pop-up when you add this product to cart
- #00 Metal Phillips 2.0mm Screwdriver Tool (PH00)
- uFix iOpener Microwaveable Heated Bag Opening Tool
- CPB 320 Repair Heat Pad for mobile phones and tablets
- Large Blue Suction Cup Opening Tool
- iGadget Plastic Triangle Opening Picks (set of 5)
- iPlastix Flexible Opening Tool by Dottorpod
- Nylon Antistatic Spudger Pry Tool
- iGadget Plastic Alcohol 200mL Bottle with Pump Top
- Tesa 61395 Double Sided Adhesive Tape 2mm
- iGadget Universal Magnetic Work Project Mat with Marker (30cm x 25cm)
Here are some helpful tips to assist you in completing a safe repair on your device. If you are unsure of something or have any questions, please feel free to contact us either by phone (0508 IGADGET) or by email
- Drain the battery below 25% before you start on this repair
- Power the iPad off before you start.
- The battery stays connected for this repair. Keep metal tools away from the battery and board, and never bend, crush or puncture the battery.
- Warm the edges with the iOpener or heat pad in short passes, as too much heat can damage the battery.
- Keep opening picks shallow along the bottom right edge, where the Wi-Fi antenna sits for about 75mm in from the corner, and use the iPlastix there.
- You're refitting the original glass, so go slowly, as forcing it can crack it.
- Always track your screws on a magnetic mat, so each goes back in the right place.
- Keep fingerprints and dust off the new LCD, and fit its cable fully into the connector before you close the flap.
- Test the picture and touch before you seal it, and leave the protective film on until the new LCD works.
- If it doesn't turn on or show a picture, force restart it by holding the top button and Home button until the Apple logo appears.
- Clean the old adhesive off with isopropyl alcohol and lay new 2mm Tesa tape round the frame before you stick the glass back down.
What’s In The Box
- 1x iPad 2 replacement LCD
