
Product Details
Need an Apple Watch SE battery replacement for your SE 2nd Gen 40mm GPS? If it drains fast, shuts down early, gets stuck in a boot loop or won't hold a charge, a worn battery is usually the cause. This is a 209mAh replacement, battery model A2721, for the GPS model (A2722).
- RATED 209mAh - 209mAh, the same rated capacity as the battery Apple fitted to the Apple Watch SE 2nd Gen 40mm GPS.
- ADHESIVE PRE-ATTACHED - The battery comes with its adhesive already fitted, so once the old adhesive is cleaned off it presses straight into the case.
- QC TESTED - Every battery is tested before it ships, with a failure rate under 1%.
- SENT FROM NZ STOCK - Shipped from our New Zealand stock, so there's no waiting weeks for a part to arrive from overseas.
Part Includes:
- Apple Watch SE 2nd Gen 40mm GPS Replacement Battery
- Pre-attached battery adhesive
- 12 Month Warranty
Please Note
Made for the GPS model (A2722) only. Does NOT fit any 44mm watch. Check Settings, General, About, Model. 40mm Cellular, Series 5 or SE? See our Series 5 / SE 40mm battery.
Please Note
Check your seal or adhesive before you start, and have new display adhesive ready to reseal the display.
Specifications
- Battery Model: A2721
- Voltage: 3.86V
- Capacity: 209mAh, 0.807Wh
- Battery Type: Lithium-ion polymer
- Pairing: Not needed. Apple Watch batteries aren't paired, so no Unknown Part message.
- Warranty: 12 Months
Compatible Model Numbers
Apple Watch SE 2nd Gen 40mm GPSModel Number (A Number)
- A2722
SE 2nd Gen 40mm Model NumbersHow do I find my Model number?
Model Identifier
- Watch6,10
EMC Number
- EMC 8090
Device Number (M Number)
- MNT33
- MNT63
- MNT73
- MNT83
- MNT93
- MNTC3
Installation Help
Check out the video above or the step by step guide below for assistance with this repair
The video shows the Apple Watch SE (1st gen), which comes apart the same way as the SE (2nd gen).
iFixit Apple Watch SE (1st gen) Battery Replacement Guide
Remember
After completing your repair, calibrate your newly installed battery by charging it to 100% and then charging for a further two hours. Use your Apple Watch until it shuts off due to low battery, and finally, charge it uninterrupted to 100% again
Here are some tools you may need to help you complete the repair.
Please note: A discounted simple toolset with the tools you need is available in a pop-up when you add this product to cart
- uFix iOpener Microwaveable Heated Bag Opening Tool
- iGadget Exacto Technician Knife with x5 blades
- iFlex Metal Flexible Opening Tool (display edge only)
- iGadget Plastic Triangle Opening Picks (set of 5)
- Y000 Metal Triwing Tri-Point 0.6mm Screwdriver Tool
- Nylon Antistatic Spudger Pry Tool
- Mechanic AK-15 King ESD Anti-Static Curved Tweezers
- iGadget Plastic Alcohol 200mL Bottle with Pump Top
- iGadget Universal Magnetic Work Project Mat with Marker (30cm x 25cm)
Here are some helpful tips to assist you in completing a safe repair on your device. If you are unsure of something or have any questions, please feel free to contact us either by phone (0508 IGADGET) or by email
- Drain the battery below 25% before you start on this repair. A charged lithium-ion battery can catch fire if it's punctured or damaged
- Power the watch off and take it off its charger before you open it
- Warm the display edge with the iOpener, then cut the adhesive with the knife, no more than about 2mm in, so you don't cut the display cables. Use the iFlex on the display edge only, never near the battery
- Open the display only to about 45 degrees: its cables are still connected underneath
- Track your screws on a magnetic mat and handle them with tweezers, so each tiny screw goes back in the right place
- The battery connector sits under a metal plate held by one 1.1mm Y000 screw. Remove the screw and plate, then lift the connector with a spudger before you touch anything else
- Keep metal tools away from the battery, and never bend, crush or puncture it. Lift the old battery slowly with a plastic pick, keeping it shallow, as the display cables run underneath it
- Remove every bit of the old battery adhesive and clean the case with isopropyl alcohol. Peel the liner from the new battery's adhesive, press the battery into place and reconnect it, then check the watch powers on and charges before you seal it
- Check your seal or adhesive before you start. Clean the old display adhesive off the case with isopropyl alcohol, fit new display adhesive and press the display down evenly while it sets
- If your watch doesn't turn on after the repair, force restart it: hold the side button and the Digital Crown together for at least 10 seconds, until the Apple logo appears
Caution
If the new battery or the battery in your device is swollen or damaged during repair, take the proper precautions
Note
You cannot dispose of old batteries in your general waste. Find recycling e-waste centres online or take to your local refuse station.
What's In The Box
- 1x Apple Watch SE 2nd Gen 40mm GPS Replacement Battery with pre-attached adhesive
